2018-2020 Kawasaki Z900 RS
USB (Denso) v3 Package
|
This package includes everything you need to start tuning your 2018-2020 Kawasaki Z900 RS with our USB (Denso) v3 and Bench Harness.- USB (Denso) v3
- USB Cable
- Kawasaki Bench Harness Type 12
- Kawasaki Data Harness Type 3
- Bin File Definition in the Woolich Racing Tuned software
View Full Product Details...
This product comes with 1 Bin File Definition Key allowing you to tune 1 ECU's as many times as you like. Additional Bin File Definition Keys are required for each additional ECU's and can be purchased from within the WRT software.
|
US$519.00
ex Sales Tax VAT
|
|
2021-2024 Kawasaki Z900 RS
Log Box (D-Can) v3 Package
|
This package includes everything you need to start tuning your
2021-2024 Kawasaki Z900RS with our Log Box (D-Can) v3
- Log Box (D-Can) v3
- USB Cable
- On board 4GB micro SD card
- Kawasaki Bench Harness Type 22
- Universal Harness Type 3 (engine data)
- Bin File Definitions in Woolich Racing Tuned Software
PLEASE NOTE: THIS D-CANV3 PACKAGE IS ONLY FOR MODELS WITH THE FOLLOWING ECU NUMBERS:
21175-1588_KPN7K8E0
21175-1840_TPP2K8E0
ALWAYS CHECK THE ECU PART NUMBER PRIOR TO ORDERING. FOR MORE ADVICE PLEASE CONTACT OUR SUPPORT CENTER.
For other ECU part numbers please see Dv3 packages below.
Note: If you are working with the EU Restricted ECU (48 pin ECU Plug), you will need the Kawasaki Bench Harness Type 23.
Please
note: Due to a change made by Kawasaki some bikes may not support
Engine Data or Diagnostics. For more information please contact us via a
Support Ticket.
View Full Product Details...
This product comes with 1 Bin File Definition Key allowing you to tune 1 ECU's as many times as you like. Additional Bin File Definition Keys are required for each additional ECU's and can be purchased from within the WRT software.
|
US$630.00
ex Sales Tax VAT
|
|
2021-2024 Kawasaki Z900 RS
Log Box (D-Can) v3 Package
+ Zeitronix ZT-3 Wideband O2 Package
|
This package includes everything you need to start tuning your
2021-2024 Kawasaki Z900 RS with our Log Box (D-CAn) v3 and Zeitronix
ZT-3 Wideband O2 Sensor. - Log Box (D-can) v3
- USB Cable
- On board 4GB micro SD card
- Kawasaki Bench Harness Type 22
- Universal Harness Type 3 (engine data only)
- Bin File Definitions in Woolich Racing Tuned Software
- Zeitronix ZT-3 Wideband O2 Controller
- Zeitronix Wideband O2 Sensor (3 foot cable)
- RJ12 cable to connect Zeitronix to Log Box
- Zeitronix Installation Kit
- O2 sensor bung
PLEASE NOTE: THIS D-CANV3 PACKAGE IS ONLY FOR MODELS WITH THE FOLLOWING ECU NUMBERS:
21175-1588_KPN7K8E0
21175-1840_TPP2K8E0
ALWAYS CHECK THE ECU PART NUMBER PRIOR TO ORDERING. FOR MORE ADVICE PLEASE CONTACT OUR SUPPORT CENTER.
For other ECU part numbers please see Dv3 packages below.
Note: If you are working with the EU Restricted ECU (48 pin ECU Plug), you will need the Kawasaki Bench Harness Type 23.
Please
note: Due to a change made by Kawasaki some bikes may not support
Engine Data or Diagnostics. For more information please contact us via a
Support Ticket.
View Full Product Details...
This product comes with 1 Bin File Definition Key allowing you to tune 1 ECU's as many times as you like. Additional Bin File Definition Keys are required for each additional ECU's and can be purchased from within the WRT software.
|
US$872.00
ex Sales Tax VAT
|
|
2018-2020 Kawasaki Z900 RS
Log Box (Denso) v3
+ Zeitronix ZT-3 Wideband O2 Package
|
This package includes everything you need to start tuning your 2018-2020 Kawasaki Z900 RS with our Log Box (Denso) v3 and Zeitronix ZT-3 Wideband O2 Sensor. - Log Box (Denso) v3
- USB Cable
- On board 4GB micro SD card
- Kawasaki Bench Harness Type 12
- Kawasaki Data Harness Type 3
- Bin File Definitions in Woolich Racing Tuned Software
- Zeitronix ZT-3 Wideband O2 Controller
- Zeitronix Wideband O2 Sensor (3 foot cable)
- RJ12 cable to connect Zeitronix to Log Box
- Zeitronix Installation Kit
- O2 sensor bung
View Full Product Details...
This product comes with 1 Bin File Definition Key allowing you to tune 1 ECU's as many times as you like. Additional Bin File Definition Keys are required for each additional ECU's and can be purchased from within the WRT software.
|
US$856.00
ex Sales Tax VAT
|
|
2021-2023 Kawasaki Z900 RS
Log Box (Denso) v3 Package
|
This package includes everything you need to start tuning your
2021-2023 Kawasaki Z900 RS with our Log Box (Denso) v3 - Log Box (Denso) v3
- USB Cable
- On board 4GB micro SD card
- Kawasaki Bench Harness Type 22
- Universal Harness Type 2
- Bin File Definitions in Woolich Racing Tuned Software
Note: If you are working with the EU Restricted ECU (48 pin ECU Plug), you will need the Kawasaki Bench Harness Type 23.
Please
note: Due to a change made by Kawasaki some bikes may not support
Engine Data or Diagnostics. For more information please contact us via a
Support Ticket.
View Full Product Details...
This product comes with 1 Bin File Definition Key allowing you to tune 1 ECU's as many times as you like. Additional Bin File Definition Keys are required for each additional ECU's and can be purchased from within the WRT software.
|
US$630.00
ex Sales Tax VAT
|
|
2021-2024 Kawasaki Z900 RS
Log Box (Denso) v3
+ Zeitronix ZT-3 Wideband O2 Package
|
This package includes everything you need to start tuning your 2021-2024 Kawasaki Z900 RS with our Log Box (Denso) v3 and Zeitronix ZT-3 Wideband O2 Sensor. - Log Box (Denso) v3
- USB Cable
- On board 4GB micro SD card
- Kawasaki Bench Harness Type 22
- Universal Harness Type 2
- Bin File Definitions in Woolich Racing Tuned Software
- Zeitronix ZT-3 Wideband O2 Controller
- Zeitronix Wideband O2 Sensor (3 foot cable)
- RJ12 cable to connect Zeitronix to Log Box
- Zeitronix Installation Kit
- O2 sensor bung
Note: If you are working with the EU Restricted ECU (48 pin ECU Plug), you will need the Kawasaki Bench Harness Type 23.
Please note: Due to a change made by Kawasaki some bikes may not support Engine Data or Diagnostics. For more information please contact us via a Support Ticket.
View Full Product Details...
This product comes with 1 Bin File Definition Key allowing you to tune 1 ECU's as many times as you like. Additional Bin File Definition Keys are required for each additional ECU's and can be purchased from within the WRT software.
|
US$856.00
ex Sales Tax VAT
|
|
2018-2020 Kawasaki Z900 RS Launch Control Key
|
Launch Control is part of the our Race Tools Package. It allows you to set a Launch RPM and also Ramp Parameters to assist with getting fast consistent launches from your bike, all controlled by the stock ECU.
If you already have a Quickshifter or Air Shifter installed on your bike or you only need the Launch Control function you can purchase this Launch Control Key. The Launch Control Key allows you to enable the Launch Control for one ECU.
Woolich Racing Race Tools requires you to Write the ECU. It is not a stand alone product. You will need to use the relevant Woolich Racing Interface and Bin File Definition to enable and configure Race Tools and write to the ECU. You can purchase this as a package on the product page for your bike. If you do not have a Woolich Racing Interface you can also visit a Woolich Racing - Tuning Partner and have them install and configure the Race Tools (additional fees and charges will apply).
View Full Product Details...
|
US$210.00
ex Sales Tax VAT
|
|
2018-2020 Kawasaki Z900 RS Race Tools Package
|
The Race Tools package allows you to enable Quickshifter, Launch Control and Pit Speed Limiter in the Stock ECU. The package includes: - High quality strain gauge Quickshifter with digitally controlled pressure sensing that can be used in regular or race shift pattern.
- Shift rod for standard shift configuration*
- Kawasaki Race Tools Harness Type 9 which allows the quickshifter to be plugged into the bikes wiring harness**
- Race Tools Key to allow the use of the Race Tools on one ECU in the Woolich Racing Tuned software.
Quickshifter Kill times are configurable per gear with 3D maps allowing Kill Times to be set for the full range of TPS and RPM combinations. The quickshifter kills ignition. Launch Control allows you to configure Delay, Launch RPM, Ramp Time and Ramp RPM Pit Speed Limiter allows you to set the RPM to limit the speed while riding through the pits.*** * Contact us after ordering if you have after-market rearsets or are using a race shift pattern and we will swap the shift rod for a generic rod that can be cut and tapped to the correct length. ** This harness uses the stock O2 Sensor plug on the bike's harness, the stock O2 sensor should be removed from the bike and disabled in our software *** Pit Speed Limiter harness sold separately
Woolich Racing Race Tools requires you to Write the ECU. It is not a stand alone product. You will need to use the relevant Woolich Racing Interface and Bin File Definition to enable and configure Race Tools and write to the ECU. You can purchase this as a package on the product page for your bike. If you do not have a Woolich Racing Interface you can also visit a Woolich Racing - Tuning Partner and have them install and configure the Race Tools (additional fees and charges will apply).
View Full Product Details...
|
US$467.00
ex Sales Tax VAT
|
|
Pit Speed Limiter Harness
|
The Pit Speed Limiter harness is used with our Race Tools Package, it consists of a harness and water proof push button switch which allows you to limit the RPM of the bike in 1st gear while riding in the pits. You must have a Race Tool Package to use the Pit Speed Limiter Harness.
The Pit Speed Limiter harness also includes a stainless steel bracket used to mount the button on the bike's switch gear.
Woolich Racing Race Tools requires you to Write the ECU. It is not a stand alone product. You will need to use the relevant Woolich Racing Interface and Bin File Definition to enable and configure Race Tools and write to the ECU. You can purchase this as a package on the product page for your bike. If you do not have a Woolich Racing Interface you can also visit a Woolich Racing - Tuning Partner and have them install and configure the Race Tools (additional fees and charges will apply).
View Full Product Details...
|
US$26.00
ex Sales Tax VAT
|
|
2021-2024 Kawasaki Z900 RS Stock Bin File Definitions
|
Purchase this item to gain access in the Woolich Racing Tuned software to the stock bin files for the 2021-2024 Kawasaki Z900 RS.
View Full Product Details...
|
ex Sales Tax VAT
|
|
Kawasaki Bench Harness Type 22 (KBH22)
|
The bench flashing harness allows you to flash the 2020-2023 Kawasaki Z900 / Z650 ECUs . The bench flashing harness comes with a 12v plug to be used in with a 12v power supply, and needs to be used in conjunction with the Woolich Racing Denso USB Interface.
Note: this product requires the purchase of bin file definitions for use with the Woolich Racing Tuned softwareNote: If you are working with the EU Restricted ECU (48 pin ECU Plug), you will need the Kawasaki Bench Harness Type 23.
View Full Product Details...
|
US$126.00
ex Sales Tax VAT
|
|
Kawasaki Bench Harness Type 23 (KBH23)
|
The bench flashing harness allows you to flash the 2020-2021 Kawasaki ECU with 48 pin ECU Plug . The bench flashing harness comes with a 12v plug to be used in with a 12v power supply, and needs to be used in conjunction with the Woolich Racing Denso USB Interface.
View Full Product Details...
|
US$126.00
ex Sales Tax VAT
|
|
Universal Harness Type 2 (UH-2)
|
This Universal harness allows you to connect to the 6 pin Red Diagnostic Plug on the bike and read and clear fault codes and view Engine data using a USB D v3, Log Box D v3, USB M v3, Log Box M v3, USB M-Ducv3 and Log Box M-Ducv3
Note: USB v3 and Log Box v3 is not included.
PLEASE NOTE - Universal Harness Type 2 (known previously as Kawasaki Data Harness Type 4)
View Full Product Details...
|
US$42.00
ex Sales Tax VAT
|
|
Universal Harness Type 3 (UH-3)
|
The Universal Harness Type 3 connects your Woolich Racing Log Box D-CAN to bikes with the newer red 6 pin OBD2 bike plug.
View Full Product Details...
|
US$42.00
ex Sales Tax VAT
|
|
Barrel to 2 Pin Plug Bench Harness Power Supply Connector
|
This harness allows you to connect the 2 pin plug used on our Bench Harnesses to a 12v Power Supply with a standard 2.5mm barrel connector.
View Full Product Details...
|
US$10.00
ex Sales Tax VAT
|
|
Kawasaki Data Harness Type 3 (KDH3)
|
Data harness used with v3 Denso Interfaces to provide Engine Data and Diagnostics for 2017+ Kawasaki Denso ECU equipped bikes.
View Full Product Details...
|
US$26.00
ex Sales Tax VAT
|
|
Kawasaki Bench Harness Type 12 (KBH12)
|
The bench flashing harness allows you to flash ECU's when they are not installed in the bike. The bench flashing harness comes with a 12v power supply plug.
Note: If you have a Z900 ECU with part number 21175-1307 or 21175-1362 you will need the Kawasaki Bench Harness Type 19
View Full Product Details...
|
US$126.00
ex Sales Tax VAT
|
|
Kawasaki Pair Valve Eliminator Type 1 (KPV-E1)
|
The Woolich Racing PAIR Valve Eliminator allows you to remove the PAIR Valve and PAIR Valve Solenoid from the motorcycle. The eliminator prevents the bike from displaying the Malfunction Indicator Light (MIL) on the dash and prevents fault codes from appearing in the diagnostic system.
The eliminator should be plugged into the bike's wiring harness before the ignition is switched back on to prevent fault codes being stored in the ECU.
Supported models:
- 2012-2021 Ninja 650
- 2012-2021 ZX14R
- 2013-2017 Ninja 300
- 2014-2021 Ninja 1000
- 2018-2021 Ninja 400
- 2009-2021 ZX6R
- 2014-2016 Z1000
- 2015-2018 Versys 1000
- 2015-2021 Vulcan S
- 2008-2021 ZX10R
- 2016-2021 Versys 650
- 2017-2021 ZX10RR
- 2017-2021 Versys X 300
- 2017-2021 Z125 Pro
- 2017-2021 Z650
- 2018-2021 Mule Pro FX
- 2018-2021 Mule Pro FXR
- 2018-2021 Mule Pro FXT
- 2018-2021 Teryx
- 2018-2021 Teryx 4
- 2019-2021 Mule Pro MX
- 2019-2021 W800 Café
- 2020-2021 KLX230
- 2020-2021 KLX230R
- 2020-2021 KLX300R
- 2020-2021 Z400
- 2021 Teryx KRX 1000
- 2008-2021 Concours 14
- 2017-2020 Z900
- 2009-2013 ZX14
- 2018-2020 Z900RS
- 2015-2021 H2
- 2019-2021 H2 SX SE - 2020-2021 Versys 1000
View Full Product Details...
|
US$41.00
ex Sales Tax VAT
|
|
| Woolich Racing Merchandise |
|
|
|
|
|
| |
|
|
There are no products for this model, please check back soon...
|
|